Skip to content
Appointment timing depends on ZIP code, route capacity, and appliance type.
Whirlpool kitchen and laundry repair. Clear estimates before any work begins.
Call (844) 968-2053
Whirlpool service — Whirlpool Washer F3E2 Code

Whirlpool

Whirlpool Washer F3E2 Code Reversed Hoses or Water Level Sensor

Book a Repair (844) 968-2053
Daniel Reeves Written by Daniel Reeves Appliance Repair Content Specialist Published October 20, 2026

Whirlpool

Code overview at a glance.

The facts for this Whirlpool error, a plain-language snapshot, and what to confirm against your model number.

Error code F3E2
Appliance Washer
Content status Verified
Quick answer

F3E2: hose and valve checks for top load washers; a water level sensor cause is listed for compact ventless towers.

Model note: Whirlpool reuses codes across series and model years, so F3E2 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Whirlpool

What this code may mean.

A plain-language reading of the code — always confirm against your model’s documentation.

If F3E2 is displayed, it could mean the hot and cold inlet hoses have been installed incorrectly.

Which washer is it?

  • Top load washer: the cold water hose may be connected to the hot inlet, with the hot hose on the cold inlet.
  • Compact ventless laundry tower, washer section: potential cause is the water level sensor.

Top load checklist

  1. Is the water on? Make sure the hot and cold valves are wide open and that both inlet hoses are attached.
  2. Are the hoses reversed? Swap them back to the right inlets if they are not.
  3. Reset the control: disconnect power for 5 minutes, either at the plug or the breaker, then reconnect.

Neighbouring codes

Water level on its own is covered under F3E1; the inlet temperature sensor is under F3E3; and F4E2 is the heating alert on compact towers.

Washer service across Miami, New York, Houston, Los Angeles and San Diego

Our Whirlpool washer service area spans the Miami, New York, Houston, Los Angeles and San Diego metros. Phone (844) 968-2053 when F3E2 persists, naming the model type and the hose and reset checks you completed.

Source: Product Help: F3E2 – Error Code; Product Help: F3E2 – Error Code

Whirlpool

Safety warning before you continue.

Stop immediately if you notice smoke, sparks, a burning smell, gas odor, or water near electrical parts.

Important

Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Whirlpool

Seeing this code on your appliance?

Book an Whirlpool appliance service visit for a clear estimate and approval before any repair.

Experienced technicians, clear diagnostics, and workmanship coverage on completed repairs.

Book a Repair (844) 968-2053

Whirlpool

Ready to restore your Whirlpool appliance?

Book a repair online or call us — clear estimates, approval before any work, and a workmanship warranty on completed repairs.

Book a Repair (844) 968-2053

Whirlpool

Tell us what’s wrong — we’ll take it from there.

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Prefer to call? (844) 968-2053
  1. Share the symptom Tell us the Whirlpool model and what’s going wrong.
  2. Confirm a window We’ll schedule a visit that fits your day.
  3. Approve before work You get a clear estimate — nothing starts without your OK.
Phone (844) 968-2053
Email info@whirlpoolservicecenter.support
Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Appointment timing depends on ZIP code, route capacity, and appliance type.
(844) 968-2053 Book a Repair